Monarch 9406 Uživatelský manuál

Monarch ® 9406™Thermal PrinterOperator’s HandbookTC9406OH Rev. B 8/94 ©1994 Monarch Marking Systems, Inc. All rights reserved.

9406 Operator’s Handbook1-6

2. Getting StartedBefore you use the 9406 printer:• Install the printer (refer to your Equipment Manual).• Load supplies (refer to your Equipment Man

Turning the Printer OnRefer to your Equipment Manual for information about installingthe printer and loading supplies.The power switch is on the back

Start UpWhen you turn the printer on, the printer displays copyright andformat loading messages. Then you will seeCalibrating...as the printer checks

To display the menu options, press the arrow keys, as follows:• When the screen displays a right arrow,MAIN MENUPrint Mode >press to display

3. Setting Supply OptionsYou may need to set supply options often to adjust for differentsupplies. The options are shown below with the default sett

2. Press . You will seeSETUPSupply >3. Press . You will see the first supply option.SUPPLYRibbon >To change one of these options, follow

3. Press to exit to the Setup menu.NOTE: If you set the Ribbon option to Yes, be sure youinstall a ribbon before printing.4. Press to exit to

3. Press or until you see the option you want. Thenpress . The printer calibrates to check the supply.You will seeSUPPLY< Supply Type &

The default setting for Dispense Mode is On-demand. Tochange the setting, follow steps listed under "Finding theSupply Options." Then foll

Each product and program carries a respective writtenwarranty, the only warranty on which the customer can rely.Monarch reserves the right to make cha

The printer does not stop between labels in continuous mode,but you can interrupt the batch. Press in the middle of thebatch to suspend printing

The default setting for Print Position is 0. To change thesetting, follow the steps listed under "Finding the SupplyOptions." Then follow

Supply PositionThis function adjusts how much supply feeds out of the exitchute. You may need to adjust the supply in or out to allow:• Labels to be

5. Press to exit to the Setup menu.6. Press to exit to the Main Menu.NOTE: After changing settings in the Setup Menu, alwaysreturn to the Main

The width of the print area is always four inches. When youmove the image to the right or left on the supply, avoid movingthe image outside the four

5. Press to exit to the Setup menu.6. Press to exit to the Main Menu.NOTE: After changing settings in the Setup Menu, alwaysreturn to the Main

9406 Operator’s Handbook3-12

4. Setting Communication ValuesYou need to set the printer communication values to match yourhost’s online communications. Before entering thecommun

2. Press . You will seeSETUPSupply >3. Press until you seeSETUP< Port Settings4. Press . You will see the first communications opti

2. Press or to display the baud rate you need, thenpress . You will seePORT SETTINGSBaud rate >3. Press to exit to the Setup menu.4

Table of Contents1. Introduction...1-1About This Manual...

3. Press or to display the word length you need, thenpress . You will seePORT SETTINGS< Word Length >4. Press to exit to the Set

3. Press or to display the number of stop bits youneed, then press . You will seePORT SETTINGS< Stopbits >4. Press to exit to th

3. Press or to display the parity you need, then press . You will seePORT SETTINGS<Parity>4. Press to exit to the Setup menu.5.

3. Press or to display the flow control you need, thenpress .NOTE: The XON character is 17. The XOFF character is19.If you have an IBM per

2. Press . You will see Are you sure?No >3. You can:• press to exit without changing the values. You willreturn to the Port Setting menu.•

5. Setting the ContrastContrast controls the darkness of the printing on your supply.The range is -50 to +50, and the default is 0. Use the followin

3. Press until you seeSETUP< Contrast >4. Press . You will see the previous setting, for exampleEnter contrast[+/-50]: +05. Use the ar

6. Setting DefaultsSome printer options can be set to fit your daily operation. Theoptions are shown below. The factory setting is in bold.Monetary

2. Press . You will seeSETUPSupply >3. Press until you seeSETUP< Defaults >4. Press . You will seeDEFAULTS< Monetary Sign >

The default setting for Monetary Sign is USA. To change thesetting, follow the steps listed under "Finding Default Options."Then follow the

4. Setting Communication Values...4-1Finding Communication Value Options...4-1Baud Rate ...

The default setting for Secondary Sign is No. To change thesetting, follow the steps listed under "Finding Default Options."Then follow the

Decimal PlacesYou can set the printer for 0, 1, 2, or 3 places after the decimalin a price field. In U.S. currency, you might print prices like this$

9406 Operator’s Handbook6-6

7. Printing OnlineYou can send format, batch, and graphic data streams to theprinter from a host. When the printer receives the data,batches begin p

If you have been using other printer functions, press untilyou see the Main Menu. Then,1. Press or until you seeMAIN MENUPrint Mode >

IndexAAdjusting margin position 3-9Adjusting print position 3-6Adjusting supply position 3-8BBaud rate 4-1CCommunication parametersBaud rate 4-1P

RResetting communicationsparameters 4-7Ribbon 3-2 - 3-3SSecondary sign, using 6-3Selecting a function 2-4Setting communication parameters 4-1S

Printed by the Technical Communications DepartmentPrinted in the U.S.A.For supplies, service, or assistance call:TOLL FREE:1-800-543-6650 (In the U.S

1. IntroductionThe 9406™ printer lets you print letters, numbers, bar codes,and graphics on labels. You can create and download formatsfrom a host.A

Other DocumentationFollowing are other manuals you might need:Equipment ManualContains general set-up andmaintenance procedures.System Administrator’s

Introduction1. Introduction1-3

New 9406 FeaturesWith the latest release of the software, the 9406 printer:• bases the dispense mechanism on the supply type anddispense mode (instead

Terms You Should Knowbatch A group of labels that contain thesame data.batch separator An extra label between batches thatshows where one batch ends a